Pride Mobility Jazzy Select (UK) – fault codes, parts & serial label
Typepowerchair (mid-wheel drive)
ControllerPG Drives VR2 (Pride UK VR2 operating instructions) CONFIRMED
Fault codes (17)
From the VR2 powerchair controller code set. All VR2 powerchair controller codes
| Code | Meaning | Checks |
|---|---|---|
| 1 bar | Low battery voltage | Check the connections to the battery. If the connections are good, try charging the battery |
| 2 bars | Left motor disconnected | Check all the connections and leads between the left motor and the power module |
| 4 bars | Right motor disconnected | Check all the connections and leads between the right motor and the power module |
| 3 bars | Left motor wiring trip | Check all the connections and leads between the left motor and the battery |
| 5 bars | Right motor wiring trip | Check all the connections and leads between the right motor and the battery |
| 6 bars | Charger connected (drive inhibited) | Disconnect the battery charger; otherwise find the external inhibit signal for this chair |
| 7 bars | Possible joystick trip | Make sure the joystick is in the centre position before switching on the VR2 |
| 8 bars | Possible control system trip | Make sure that all connections are secure |
| 9 bars | Solenoid brake trip | Check the parking brake and motor connections. Make sure all the system connections are secure |
| 10 bars | High battery voltage | Check the battery connections |
| Speed LEDs flash with the gauge (+S) | Communication fault | Check the cable and plugs between joystick and power module; cycle the power |
| Actuator LED flashes with the gauge (+A) | Actuator trip | Check the actuator wiring and plugs |
| Battery gauge steps up | Charging (drive inhibited) | No drive until the charger is unplugged and the power switched off and on |
| Speed indicator ripples up and down | Chair locked | Unlock it with the key or the joystick unlock sequence in the chair manual |
| Speed indicator flashes | Speed limited | Lower the seat to drive at full speed |
| Battery gauge ripples at power-on | Joystick displaced | Centre the joystick, switch off and on again |
| Gauge blinks every 2.5 seconds | Sleep mode | Switch off and on again |
Serial code label
No serial location data yet for this powerchair. Serial codes
Parts (19)
| Part | Part no. |
|---|---|
| CASTER,ASSY,6" FLAT-FREE WHEEL,RIGHT,SELECT,VERSION 2 | FRMASMB14262 |
| CASTER,ASSY,6" FLAT-FREE WHEEL,LEFT,SELECT,VERSION 2 | FRMASMB14261 |
| CASTER,ASSY,6" FLAT-FREE WHEEL,RIGHT,JAZZYSELECT,D-1060-018 | FRMASMB9219 |
| CASTER,ASSY,6'' FLAT-FREE WHEEL,LEFT,JAZZYSELECT,D-1060-017 | FRMASMB9218 |
| CASTER,ASSY,6" FLAT-FREE WHEEL,SILVER RIM/BLACKTIRE,RIGHT,JAZZYSELECT,VERSION 2,D-1202-034 | CASASMB7110004 |
| CASTER,ASSY,6" FLAT-FREE WHEEL,SILVER RIM/BLACKTIRE,LEFT,JAZZYSELECT,VERSION 2,D-1202-034 | CASASMB7110002 |
| MOTOR,ASSY,DRIVE,FLEET READY SELECT 6,RIGHT,W/FREEWHEEL & MOUNTING HARDWARE,VR2 CONNECTOR,D-1060-079 | DRVASMB7110014 |
| MOTOR,ASSY,DRIVE,FLEET READY SELECT 6,LEFT,W/FREEWHEEL & MOUNTING HARDWARE,VR2 CONNECTOR,D-1060-078 | DRVASMB7110013 |
| MOTOR,ASSY,DRIVE,JAZZYSELECT6,RIGHT,W/FREEWHEEL & MOUNTING HARDWARE,GC3 CONNECTOR,D-1060-047 | DRVASMB2246 |
| MOTOR,ASSY,DRIVE,JAZZYSELECT6,LEFT,W/FREEWHEEL & MOUNTING HARDWARE,GC3 CONNECTOR,D-1060-046 | DRVASMB2247 |
| MOTOR,ASSY,DRIVE,JAZZYSELECT6,RIGHT,W/FREEWHEEL & MOUNTING HARDWARE,GC3 CONNECTOR,D-1060-079 | DRVASMB2514 |
| MOTOR,ASSY,DRIVE,JAZZYSELECT6,LEFT,W/FREEWHEEL & MOUNTING HARDWARE,GC3 CONNECTOR,D-1060-078 | DRVASMB2513 |
| CONTROLLER,VR2,ASSY,40 AMP,1 ACTUATOR,SELECT6ULTRA | ELEASMB5652 |
| ELECTRONIC,CIRCUIT BREAKER,30 AMP | ELECBRK1005 |
| WHEEL,ASSY,FLAT FREE,SILVER RIM/BLACK TIRE,10",D-1203-065 | WHLASMB2045 |
| WHEEL,ASSY,FLAT FREE,BLACK STEEL DISH,3.00-4,C9210,W/FORGED STEEL HUB & HUBCAP,E-1060-093 | WHLASMB1728 |
| TIRE,W/FLAT FREE INSERT,3.00-4",C-9210-1,(GALLOP: 5504014) | TIRSOLI1020 |
| CHARGER,ASSY,OFFBOARD,100V-240V,5 AMP,BATTERY MAXIMIZER,W/EUROPEAN POWERCORD | ELEASMB6295 |
| BATTERY,AGM,U1 | BATLIQ1017 |
Summarised from public manuals and supplier listings. Always check the product's own manual before any repair.